- 시그널 컨디셔닝, 디지타이팅, 레코딩의 모든 기능 포함
- DSO(Digital Storage Oscilloscope), Transient Recorder,
FTT Analyzer 기능 통합
- 각 채널 당 2MS/s 샘플링 속도, 16비트 resolution
- 전 채널 200kS/s의 스트리밍 속도
- 네트워크 PC를 통한 실시간 제어 가능
- Main Frame과 모듈의 Mix & Match
Appr. 42 x 33 x 16 cm (17 x 13 x 6 in). Removable protective corners add approximately 3x2x2 cm
Appr. 16 kg (35 lb.)
100 mm VESA® mounting holes for swingarms, etc.
90-240 Vac, 47-63 Hz, 450 W max
20 g 11 ms half-sine, Mil-Std-810F, Procedure I
2 g, 35-500 Hz, Mil-Std-810F, Procedure I
<20,000 feet (6100 m)
Sample Clock In/Out, Calibration Signal Out ±1.5625V, Trigger Arm, External Trigger In/Out, Remote Start/Stop
Decimal rates 2 MS/s to 0.5 S/s in 1, 2, 5 steps
Binary rates 1.024 MS/s to 0.512 S/s.
Ext. Clock to 2 MS/s (>33K RPM at 3600 ppr)
<50 ppm standalone ; synchronized to national standards with GPS or IRIG input
Abs Time Accuracy
With IRIG/GPS option <1 μs, PC time accuracy without
64 MS per 4-channels (optional)
64 samples to max transient memory in scope
mode, unlimited length in recorder mode
1 sample to 100% sweep length in scope mode, up to full disk in recorder mode
1 – 1E9 samples, 1 – 64K trigger events
Any input channel, +/-/dual slope with variable hysteresis; DSP-computed measurements from any channel, or External
OR of all channels, plus separate Gate input
Up to 65,536 segments with time stamps
Up to 65,536 sweeps, selectable artifact rejection
Bandwidth, Filt off
Appr. 1 MHz at -3 dB
Bandwidth, Filt on
80 kHz at 0.1 dB flatness, user-selectable lower frequencies
Selectable - Steep-slope for best frequency response or Smooth for best time-domain step response
Max/Min, other statistical information saved in real time for accurate live displays and fast review
80 kHz bandwidth, streaming to disk at up to 204.8 kS/s per channel. In continuous mode, data may be saved to Windows HD at full rate or USB flash, RAID, server, or other storage medium at media-dependent rates.
1 MHz bandwidth, 2 MS/s 16-bit digitizer per channel.
Single-shot or repetitive mode. High-speed transient RAM storage.
Real-time FFT analysis up to 1 MHz with or without
simultaneous time-domain displays.
Both time-domain and frequency-domain averaging are provided to reduce noise and increase resolution.
Universal Signal Conditioning
Each channel software selected for single-ended or differential voltage, DC bridge, accelerometer and thermocouple inputs. Additionally, all channels may be set to measure Frequency, Mean or RMS value of their inputs in real time for storage as a trace and/or for triggering.
Insulated BNC/channel, plus multi-pin D connector per 4 channels
±20 mV to ±20 V; to 40kV with scope probes
Full, half, 1/4 bridge software selectable
1 - 10 Vdc up to 30mA/ch.
Auto or Manual
4 mA constant current, 24 Volt compliance. For ICP®- type accels, also charge-mode accels via small external charge converter
Measure physical input, enter datasheet sensitivity, or switch in bridge shunt cal resistor.
J, K, E, T type, selectable per channel
Microsoft Windows XP Professional®.
Software runs on Synergy CPU or networked PC.
Individual channel controls or spreadsheet setup
Scans inputs for active signals to set range and timebase
Scope, stripchart, XY, FFT, waterfall, zoom
DAT (Synergy native binary), 5 styles of single and multi-channel ASCII, DADiSP, WFM, SDF, DYD, WFT
All functions are available to external programs via DCOM/ActiveX®/.NET
Support for Virtual Instrument components (VI’s) for National Instruments’ LabVIEW are available on request